Raised Source/Drain (RSD)

Keywords: raised source drain structure,raised sd epitaxy,elevated source drain,rsd contact resistance,raised sd integration

Raised Source/Drain (RSD) is the structural enhancement where selective epitaxial silicon growth elevates the source/drain surface 20-80nm above the original silicon level — providing increased volume for silicide formation, reduced contact resistance, lower parasitic resistance, and improved contact landing tolerance, while serving as a platform for stress engineering through SiGe epitaxy in PMOS devices.

RSD Formation Process:

• Selective Epitaxy: after source/drain implantation and before silicidation, selective silicon epitaxy grows only on exposed silicon surfaces (S/D regions), not on gate or spacer dielectrics
• Growth Chemistry: SiH₄ or SiH₂Cl₂ precursor with HCl at 600-750°C; HCl etches nucleation on oxide/nitride surfaces, ensuring selectivity; growth rate 5-20nm/min
• Raised Height: typical RSD height 30-60nm for logic processes; taller structures provide more silicide volume but increase topography and contact aspect ratio
• In-Situ Doping: phosphorus (PH₃) for NMOS or boron (B₂H₆) for PMOS added during growth; active doping >10²⁰ cm⁻³ provides low contact resistance without additional implantation

Facet Control:

• Crystal Planes: epitaxial silicon naturally grows with {111} and {311} facets; facet angles 54.7° for {111}, 25° for {311} relative to (100) surface
• Growth Conditions: temperature, pressure, and precursor ratios control facet formation; higher temperature favors {111} facets, lower temperature produces more {311}
• Facet Uniformity: uniform facets ensure consistent silicide thickness across the S/D region; non-uniform facets cause silicide thickness variation and contact resistance variation
• Lateral Growth: some lateral epitaxy occurs under spacer edges; controlled lateral growth can reduce S/D-to-gate spacing and series resistance; excessive growth causes gate shorts

Contact Resistance Reduction:

• Silicide Volume: raised S/D provides 2-3× more silicon volume for silicide formation; thicker NiSi (20-30nm vs 10-15nm on flat S/D) reduces contact resistance
• Contact Area: raised surface improves contact landing; misaligned contacts still land on raised S/D rather than spacer or STI; improves yield and reduces resistance variation
• Specific Contact Resistivity: ρc = 1-3×10⁻⁸ Ω·cm² for NiSi on heavily-doped raised S/D; 30-50% lower than flat S/D due to better silicide quality and thickness
• Total Contact Resistance: Rc reduced 40-60% with RSD vs flat S/D; particularly important at advanced nodes where contact resistance dominates total resistance

Parasitic Resistance Benefits:

• Series Resistance: raised S/D reduces total series resistance (Rsd) by 20-40%; more conductive volume between contact and channel reduces spreading resistance
• Sheet Resistance: heavily-doped epitaxial layer has sheet resistance 50-100 Ω/sq vs 200-400 Ω/sq for implanted S/D; lower Rsh reduces lateral resistance
• Resistance Scaling: as devices shrink, parasitic resistance becomes larger fraction of total; RSD maintains acceptable Ron even as channel resistance decreases
• Performance Impact: 10-15% drive current improvement from reduced parasitic resistance; enables meeting performance targets without aggressive channel scaling

Integration with Strain Engineering:

• SiGe Raised S/D: for PMOS, grow Si₁₋ₓGeₓ instead of Si; combines raised S/D benefits (low resistance) with strain engineering (compressive channel stress)
• Dual Benefits: SiGe RSD provides both 20-30% mobility enhancement (from stress) and 30-40% resistance reduction (from raised structure); total performance improvement 40-60%
• Process Simplification: single epitaxy step provides both strain and raised S/D; eliminates need for separate recess etch and raised epi steps
• NMOS Options: some processes use raised Si:C (silicon-carbon) for NMOS to provide tensile stress; carbon content 0.5-2% induces tensile strain

Topography Management:

• CMP Challenges: raised S/D creates 30-60nm topography; subsequent contact CMP must handle this step height without dishing or erosion
• Planarization: thick interlayer dielectric (ILD) deposition and CMP planarizes surface before contact formation; requires 200-400nm ILD overburden
• Contact Aspect Ratio: raised S/D increases contact depth by the raised height; 50nm raised S/D adds 50nm to contact depth; affects contact etch and fill processes
• Design Rules: raised S/D topography affects lithography focus; design rules may restrict dense S/D patterns or require dummy fills for planarization

Process Optimization:

• Temperature: 650-700°C provides good selectivity and growth rate; lower temperature (<600°C) improves selectivity but reduces throughput; higher temperature (>750°C) risks loss of selectivity
• HCl/Precursor Ratio: ratio 0.1-0.3 optimizes selectivity vs growth rate; higher HCl improves selectivity but reduces growth rate and can etch silicon
• Pressure: 10-100 Torr; lower pressure improves uniformity and selectivity; higher pressure increases growth rate
• Doping Uniformity: in-situ doping must be uniform throughout raised region; doping gradients cause contact resistance variation; requires stable gas flow and temperature

Advanced RSD Techniques:

• Multi-Layer RSD: bottom layer high-doping Si for low resistance, top layer SiGe for stress; provides optimized resistance and strain
• Selective RSD: raised S/D only on critical devices (minimum gate length); longer gates use flat S/D; reduces process complexity while optimizing performance
• Ultra-Raised S/D: 80-120nm raised height for maximum contact area and resistance reduction; used in some high-performance processes despite topography challenges
• Facet Engineering: controlled facet angles optimize stress transfer to channel; steeper facets provide more vertical stress component

Reliability Considerations:

• Silicide Uniformity: non-uniform raised S/D causes non-uniform silicide; thin silicide regions have high resistance and poor reliability
• Defect Density: epitaxial defects (dislocations, stacking faults) degrade junction leakage and reliability; defect density <10⁴ cm⁻² required
• Stress Effects: raised SiGe S/D creates high stress at gate edge; stress concentration can affect gate dielectric reliability; requires careful stress management
• Electromigration: current crowding at contact-to-raised-S/D interface affects electromigration; contact design must account for current density

Scaling Considerations:

• FinFET Transition: raised S/D becomes essential in FinFET structures; provides landing area for contacts on narrow fins (7-10nm wide)
• Contact Scaling: as contact size shrinks below 40nm, raised S/D becomes mandatory for acceptable contact resistance; flat S/D cannot meet resistance targets
• Epitaxy Challenges: selective epitaxy on narrow structures (<20nm) is challenging; requires advanced precursors and process control
• Alternative Materials: cobalt or ruthenium replacing tungsten in contacts benefits from raised S/D landing area; enables aggressive contact scaling

Raised source/drain structures are the essential enabler of low contact resistance in scaled CMOS — by providing increased volume for silicide formation and improved contact landing tolerance, RSD reduces parasitic resistance by 30-50% while serving as the platform for strain engineering, making it indispensable from 65nm planar CMOS through 5nm FinFET technologies.

Source: ChipFoundryServices — Search this topic — Ask CFSGPT