Copper Process
The copper process builds damascene interconnect — etch the trench and via first, then electroplate copper into it and polish the excess back with CMP — the exact reverse build order from aluminum's deposit-then-etch flow. Copper can't be dry-etched the way aluminum is, because it doesn't form a volatile halide a plasma can pump away, so damascene isn't a stylistic choice; it's the only practical way to pattern copper at all, and everything else about the process follows from that constraint.
Copper needs its barrier for a more urgent reason than aluminum ever did — it doesn't just corrode nearby materials, it poisons the silicon itself. Aluminum's main diffusion hazard is spiking a shallow junction during a high-temperature anneal, a problem solved by alloying in a small silicon fraction. Copper diffuses through silicon dioxide and silicon far more readily, as an interstitial atom, and once inside silicon it forms deep-level traps that capture carriers and devastate transistor performance — even trace contamination, well below what would visibly damage a structure, can ruin device yield. That severity is why a Ta/TaN barrier under copper isn't an optional adhesion layer the way Ti sometimes is under aluminum; it is a hard requirement everywhere copper is anywhere near active silicon, chosen specifically because tantalum and its nitride resist copper diffusion better than the titanium-based barriers used elsewhere in the stack.
The additive package in the electroplating bath, not the plating current alone, is what actually achieves bottom-up fill. Left to plain electrochemistry, copper would deposit at roughly the same rate everywhere exposed to the plating bath — including the mouth of a narrow via — and pinch the opening shut long before the bottom fills, trapping a void exactly like an unassisted conformal deposition would. Accelerator molecules adsorb preferentially at the bottom of a feature as it narrows and locally speed up deposition there, while suppressor molecules slow deposition on open, flat surfaces; a leveler component further smooths the final surface topography. Tuning that three-component additive chemistry, not the trench geometry itself, is what lets a single electroplating bath fill both a wide line and a narrow via without voiding — arguably the single most important chemistry innovation that made copper damascene manufacturable at scale in 1997.
Copper's electromigration failure mode is different from aluminum's, and that difference reshaped where the fix has to go. Where aluminum interconnect fails by forming voids distributed along the length of a line, copper's higher resistance to bulk electromigration pushes the dominant failure site to the via bottom — current crowding and interface quality at the copper-to-barrier or copper-to-cap boundary beneath a via turn out to be the weak point, not the line itself. That shifted engineering focus toward capping the top of a copper line with a material that bonds better to copper than a plain dielectric does; cobalt-based caps (CoWP, or more recently a thin cobalt layer) selectively deposited onto exposed copper before the next dielectric goes down measurably extend electromigration lifetime by strengthening exactly that interface, in a way a bulk alloy addition — the aluminum fix — can't address because the problem isn't in the bulk of the line at all.
CMP removes the overburden, but what's left behind afterward — dishing and erosion — is its own engineering discipline, not a side effect to tolerate. Polishing a wafer with wide copper features next to narrow ones at different removal rates leaves wide lines slightly concave ("dishing") and dense arrays of lines slightly thinner than isolated ones ("erosion"), both of which affect the uniformity of the next metal level landing on top. Dummy fill patterns — copper or dielectric shapes added purely to even out local pattern density across the layout, with no electrical function at all — exist specifically to keep CMP removal rates consistent enough that dishing and erosion stay within a tolerance the next process step can live with.
Read the copper process as damascene's answer to every constraint copper's own chemistry imposes: it can't be dry-etched, so the metal goes in after the pattern instead of before; it poisons silicon readily, so the barrier requirement is categorical rather than optional; plain electroplating would void a narrow via, so the fill chemistry itself does the geometric work a different deposition method might have handled passively; and because its electromigration weak point sits at an interface rather than in the bulk, the fix lives in a cap layer rather than in the alloy — four different engineering responses, each one tracing straight back to a specific property of the metal that aluminum simply didn't share.