Fsg Process

The FSG process deposits fluorine-doped silicate glass — PECVD oxide with a few atomic percent of fluorine substituted into the silicon-oxide network — and it is the one dopant swap in this oxide family aimed at lowering dielectric constant rather than enabling reflow or gettering, making it BEOL's answer to the same trade-off the BPSG, PSG, and USG processes already solved for the pre-metal dielectric sitting closer to silicon.

TEOS/SiF4 + O2 (PECVD)
Fluorine source gas added to standard oxide chemistry
F substitutes into the Si-O network
Electronegative fluorine lowers network polarizability
Dielectric constant drops
k falls from ~4.1 to ~3.5-3.7
2-4 at% F is the typical production window
RC delay improves on Al interconnect
Lower k directly cuts interline capacitance
F content capped near 4-6 at%
Beyond this, the film absorbs moisture and forms HF
Moisture-driven corrosion risk
HF slowly attacks exposed aluminum lines over time
Superseded by carbon-doped oxide at 90nm
OSG (Applied Materials Black Diamond-class films) reaches k 2.7-3.0 without fluorine's corrosion risk

The physics is straightforward substitution, not a new deposition mechanism. TEOS or silane PECVD oxide normally forms a dense Si-O-Si network with a dielectric constant around 4.0-4.2; adding SiF4 to the plasma chemistry lets fluorine atoms terminate some of those Si-O bonds in place of oxygen, and because fluorine is more electronegative than oxygen, the resulting Si-F bonds polarize less easily under an applied field, pulling the bulk dielectric constant down toward 3.5-3.7 at a practical 2-4 atomic-percent fluorine loading. That drop matters directly at the interconnect level: capacitance between adjacent metal lines scales with the dielectric constant of whatever sits between them, so an FSG interlevel dielectric cuts RC delay and crosstalk on the same Al or early-Cu wiring pitch without requiring any change to the metal itself.

Oxide familyDopantTypical kPrimary benefitMain risk
BPSGBoron + phosphorus~4.0-4.2Low-temperature reflow, Na+ getteringBoron out-diffusion into silicon
PSGPhosphorus only~4.0-4.1Na+ gettering, no boron riskStill somewhat hygroscopic
USGNone~4.0-4.2Chemically inert, safe against metalNo reflow, no gettering
FSGFluorine~3.5-3.7Lower k, less RC delay/crosstalkHF formation above ~4-6 at% F
OSG / CDOCarbon (methyl groups)~2.7-3.0Lower k than FSG, no corrosion riskLower mechanical strength, CMP-sensitive
FSG: Dielectric Constant vs. Fluorine Loading k falls steadily with fluorine content, until moisture uptake sets a hard ceiling k 4.2 3.2 Fluorine content (atomic %) 0 4 8 production window k ≈ 3.5-3.7 at 2-4 at% F above ~6 at% F film absorbs moisture HF forms at anneal attacks exposed Al lines k gain no longer worth it the curve keeps bending the right way past 6 at% — the film chemistry just stops being safe enough to follow it there

That production window is also exactly why FSG never chased the lowest achievable k the way its successor did. Pushing fluorine loading past roughly 4-6 atomic percent keeps lowering the dielectric constant on paper, but the film stops being thermally and chemically stable at that concentration — unincorporated or weakly bonded fluorine reacts with ambient moisture during subsequent anneal steps to form hydrofluoric acid, which then slowly attacks any exposed aluminum interconnect it contacts, a corrosion failure mode with nothing in common with BPSG's boron diffusion or PSG's gettering trade but cutting from the same cloth: every dopant buys a property improvement by accepting a new release-and-react risk at the margins of its process window. That ceiling is what eventually priced FSG out of leading-edge BEOL — once copper interconnect and sub-130nm pitches needed k well under 3.0 to keep RC delay in check, fabs moved to carbon-doped oxide instead of pushing fluorine content any further.

Read the FSG process as fluorine's answer to USG's inertness: USG accepts zero dopant benefit to guarantee zero dopant risk, while FSG accepts a real but bounded corrosion risk in exchange for a dielectric constant improvement that BPSG, PSG, and USG — built from the same base PECVD chemistry — have no path to delivering at all.

Take FSG process further

Ask the copilot about this term, or have our engineers assess it against your process.