Gate-All-Around GAA Nanosheet Channel Release Sige Selective Etch MBCFET Ribbonfet

Where finfet-fin-patterning-sadp-saqp-process starts from a single-crystal silicon fin etched straight out of the substrate, the gate-all-around nanosheet architecture starts from something that has to be built before it can be patterned at all: an epitaxial superlattice stack of alternating silicon and silicon-germanium layers, typically three to four silicon "sheets" each a few nanometers to around eight nanometers thick, separated by sacrificial silicon-germanium layers of similar thickness, grown one on top of the other on the substrate before any fin-like shape exists. This stack is the raw material the rest of the process operates on, and the two materials play opposite roles from the moment they are grown: the silicon layers are the future transistor channels, while the silicon-germanium layers exist purely to be removed later and never carry current themselves. That sacrificial role is worth stating plainly because this batch has already used silicon-germanium for a completely different job in source-drain-epitaxy-strained-channel-process, where silicon-germanium is grown directly in the source/drain regions specifically to stay in the finished device and mechanically strain the channel for mobility; here, inside the gate-all-around stack, silicon-germanium is grown specifically so that it can be etched away again, and confusing the two uses, strain-engineering silicon-germanium that stays versus superlattice silicon-germanium that is sacrificed, is one of the easiest ways to misread how this transistor is actually built.

Once the superlattice is grown, the stack is patterned much the way a fin is patterned, an anisotropic etch cutting vertical sidewalls down through the full alternating stack to define the lateral shape the eventual nanosheet channels will share, conceptually the same fin-patterning operation named in finfet-fin-patterning-sadp-saqp-process but now cutting through several alternating material layers instead of one uniform crystal. A dummy gate and spacer are then formed over the stack using the same replacement-gate strategy already established in high-k-metal-gate-hkmg-process, a sacrificial placeholder gate that protects the channel region through the high-temperature steps that follow and gets pulled out later, and source/drain epitaxy is grown at the exposed ends of the stack using the strain-engineering concept from source-drain-epitaxy-strained-channel-process, except now that epitaxial growth has to make electrical contact with every silicon sheet in the stack simultaneously rather than with a single fin, merging around the stack ends to form one continuous source or drain region that all the sheets terminate into.

Si/SiGe superlattice epitaxy
Alternating Si (channel) and sacrificial SiGe layers, 3-4 Si sheets grown on substrate
Stack patterning
Anisotropic etch cuts fin-like lateral shape through full superlattice, concept from finfet-fin-patterning-sadp-saqp-process
Dummy gate + spacer
Replacement-gate placeholder, same concept as high-k-metal-gate-hkmg-process
Source/drain epitaxy at stack ends
Strain-engineering epi from source-drain-epitaxy-strained-channel-process, now contacting every sheet at once
Dummy gate removal
Exposes Si/SiGe stack inside the gate cavity
Selective SiGe release etch
Removes ONLY sacrificial SiGe between sheets; Si sheets left suspended, anchored at S/D ends
HKMG wraps every suspended sheet
High-k/metal fill deposits conformally around all 4 sides of each Si nanosheet
Gate-all-around transistor complete
Gate wraps full channel perimeter on every sheet

The step that actually defines this architecture happens after the dummy gate is pulled out: with the Si/SiGe stack exposed inside the gate cavity, a highly selective lateral etch, typically a dry or wet chemistry chosen to attack silicon-germanium while leaving silicon essentially untouched, removes only the sacrificial silicon-germanium layers from between the silicon sheets. Because that selectivity has to hold laterally, reaching in from the gate cavity sidewalls to clear germanium out from between sheets that may only be a few nanometers apart, without nicking the silicon sheets themselves or undercutting the source/drain epitaxy at the stack ends, this release etch is one of the most selectivity-critical steps in the entire flow: insufficient selectivity leaves germanium residue that blocks gate material from fully wrapping the sheet, while excessive aggressiveness can thin or damage the suspended silicon itself. Once the silicon-germanium is cleared, what remains are silicon nanosheets suspended in the gate cavity, mechanically anchored only at their source and drain ends, with open space on all four sides, top, bottom, and both lateral faces, where the sacrificial layer used to be. The high-k dielectric and metal gate fill, deposited with the same atomic-layer-deposition and conformal-metal-fill concept already used in high-k-metal-gate-hkmg-process, now has to flow into those narrow inter-sheet gaps and coat every exposed surface, which is what "gate-all-around" literally means: the gate material fully encircles the channel's perimeter, a four-sided wrap, rather than draping over three sides of a standing fin the way a FinFET's gate does.

CharacteristicFinFET (three-sided gate wrap)GAA nanosheet (four-sided gate wrap)
Electrostatic controlStrong, but channel bottom remains gate-uncontrolled, limiting subthreshold swing and DIBL improvement versus planarFull channel perimeter under gate control; further improves subthreshold swing and DIBL beyond FinFET
Effective channel width tunabilityFixed by fin height set during patterning; width scaling requires adding more finsNanosheet width and sheet count per stack are independent design knobs, not tied to a fixed vertical fin height
Process complexityMature flow: fin pattern, STI reveal, replacement gate, strain epiAdds epitaxial superlattice growth and a highly selective lateral SiGe release etch on top of the same replacement-gate flow
Adoption node / companyDominant from the 2010s FinFET generation through late sub-10nm nodesSamsung MBCFET at 3nm, Intel RibbonFET at 20A/18A-class, TSMC's planned N2 nanosheet node

That four-sided wrap is the direct answer to a limitation FinFETs could not design around: a fin's height is fixed once patterning locks it in, so increasing a FinFET's effective drive width means adding more fins side by side, while a gate-all-around nanosheet stack lets designers tune channel width and the number of stacked sheets independently of any fixed vertical dimension, giving the standard-cell and SRAM design teams a continuously adjustable sizing knob that FinFET's fin-counting approach never offered. That flexibility does not come for free: growing a multi-layer epitaxial superlattice before patterning even begins, and then performing a release etch selective enough to clear germanium from gaps only a few nanometers wide without damaging the silicon sheets it leaves behind, adds real process steps and tighter selectivity windows on top of everything FinFET already required, which is part of why the industry's move to gate-all-around tracks closely with the move to the most advanced nodes, where the electrostatic and width-tunability gains are judged worth that added complexity.

Gate-All-Around Nanosheet Channel Release From an epitaxial Si/SiGe superlattice to suspended sheets fully wrapped by the gate 1 · Si/SiGe superlattice 3-4 Si sheets, sacrificial SiGe grown between them 2 · Dummy gate + S/D epi dummy gate over stack, strained epi at both ends 3 · Dummy gate removed stack exposed inside the gate cavity 4 · SiGe release etch SiGe cleared laterally; sheets suspended 5 · HKMG wraps sheets gate material fully surrounds each sheet The selective lateral SiGe release etch is the step that defines this architecture: silicon sheets, anchored only at the source/drain ends, are left suspended with open space on all four sides High-k/metal fill then flows into those inter-sheet gaps and coats every exposed surface — the gate material fully encircles each channel's perimeter Silicon channel sheet Sacrificial SiGe Dummy gate High-k/metal gate fill Three-sided FinFET wrap vs. four-sided GAA wrap Same gate materials, different channel geometry and coverage FinFET: 3-sided gate wrap gate covers top + both sides; bottom sits on substrate, uncontrolled GAA nanosheet: 4-sided gate wrap sheet suspended; gate wraps top, bottom, and both sides A fin's height is fixed once patterning locks it in; a nanosheet stack's width and sheet count are independent sizing knobs FinFET never offered "Gate-all-around" means the gate wraps the full channel perimeter, not just three of four sides Silicon channel (fin or sheet) Gate material wrap Isolation / substrate

Gate-all-around nanosheet is the FinFET-era toolkit's next device-architecture generation, not a wholesale replacement of it: the replacement-gate concept from high-k-metal-gate-hkmg-process, the strained source/drain epitaxy concept from source-drain-epitaxy-strained-channel-process, and the anisotropic stack-patterning etch that echoes finfet-fin-patterning-sadp-saqp-process all carry forward essentially unchanged in purpose, they are simply applied around a fully suspended, multi-sheet silicon channel instead of around a single standing fin. What is genuinely new is the epitaxial superlattice growth step and the highly selective lateral silicon-germanium release etch that turns that stack into suspended sheets, a pair of steps with no FinFET equivalent, needed specifically because wrapping a gate around all four sides of a channel first requires suspending that channel in open space rather than leaving it anchored to the substrate the way a fin is. Extending the same gate-electrostatics logic that drove the planar-to-FinFET transition one generation further, from three sides of control to four, gate-all-around nanosheet closes out the fin-based architectural arc this batch has traced and opens the industry roadmap's current leading edge at Samsung's, Intel's, and TSMC's most advanced nodes.

Take gate-all-around GAA nanosheet channel release SiGe selective etch MBCFET RibbonFET further

Ask the copilot about this term, or have our engineers assess it against your process.