Embedded SiGe Source/Drain

Keywords: embedded sige source drain,sige epitaxy pmos,sige recess etch,sige stress engineering,selective epitaxial growth

Embedded SiGe Source/Drain is the strain engineering technique that replaces silicon in PMOS source/drain regions with epitaxially-grown silicon-germanium alloy — exploiting the 4% larger lattice constant of SiGe to induce compressive stress in the channel when constrained by surrounding silicon, achieving 20-40% hole mobility enhancement and enabling aggressive PMOS performance scaling at 65nm node and beyond.

SiGe Epitaxy Process:

• Recess Etch: after gate and spacer formation, anisotropic reactive ion etch (RIE) removes silicon from source/drain regions; etch depth 40-100nm, width defined by spacer; Cl₂/HBr chemistry provides vertical profile with minimal lateral undercut
• Recess Shape: sigma-shaped recess (faceted sidewalls) vs rectangular recess; sigma recess provides more SiGe volume and higher stress but requires careful etch control; facet angles typically {111} or {311} planes
• Cleaning: post-etch clean removes native oxide and etch residue; dilute HF (DHF 100:1) followed by H₂ bake at 800-850°C in epitaxy chamber provides atomically clean silicon surface
• Selective Epitaxy: low-temperature epitaxy (550-700°C) grows SiGe only on exposed silicon, not on oxide or nitride surfaces; SiH₂Cl₂/GeH₄/HCl chemistry; HCl suppresses nucleation on dielectrics

Germanium Content Optimization:

• Ge Concentration: 20-40% Ge typical; higher Ge provides more stress but increases defect density and process complexity; 25-30% Ge optimal for most processes
• Stress Generation: 1% Ge mismatch generates approximately 100MPa compressive stress; 30% Ge produces 800-1200MPa channel stress depending on geometry
• Lattice Mismatch: SiGe lattice constant 4.2% larger than Si at 30% Ge; mismatch creates compressive stress when SiGe is constrained by surrounding silicon substrate
• Critical Thickness: SiGe films thicker than critical thickness (60-100nm for 30% Ge) relax stress through dislocation formation; recess depth must stay below critical thickness

In-Situ Doping:

• Boron Incorporation: B₂H₆ added during epitaxy provides in-situ p-type doping; active doping concentration 1-3×10²⁰ cm⁻³ achieves low contact resistance
• Doping Uniformity: boron concentration must be uniform throughout SiGe film; concentration gradients cause stress gradients and non-uniform contact resistance
• Activation: as-grown SiGe has >90% dopant activation; minimal additional activation anneal required; reduces thermal budget compared to implanted S/D
• Segregation: boron segregates to SiGe/Si interface during growth; can create high-doping spike at interface beneficial for contact resistance

Stress Transfer Mechanism:

• Lateral Stress: SiGe in S/D regions pushes laterally on channel silicon; compressive stress along channel direction (longitudinal) enhances hole mobility
• Stress Magnitude: channel stress 800-1200MPa for 30% Ge, 40-80nm recess depth, and 30-50nm gate length; stress increases with Ge content and recess depth
• Gate Length Dependence: shorter gates receive more stress; stress ∝ 1/Lgate approximately; 30nm gate has 1.5-2× stress of 60nm gate
• Width Dependence: narrow devices (<100nm width) have reduced stress due to STI proximity; stress modeling must account for 2D geometry effects

Performance Enhancement:

• Mobility Improvement: 30-50% hole mobility enhancement at 30% Ge; mobility improvement saturates above 35% Ge due to alloy scattering in SiGe
• Drive Current: 20-35% PMOS drive current improvement at same gate length and Vt; enables PMOS to match NMOS performance (historically PMOS 2-3× weaker)
• Balanced Performance: embedded SiGe combined with tensile NMOS stress (from CESL or SMT) provides balanced NMOS/PMOS performance; critical for circuit design
• Scalability: SiGe stress effectiveness increases at shorter gate lengths; provides continued benefit through 22nm node before FinFET transition

Integration Challenges:

• Recess Control: recess depth and profile uniformity critical; ±5nm depth variation causes 10-15mV Vt variation and 3-5% performance variation
• Facet Formation: uncontrolled faceting during epitaxy can cause non-uniform SiGe thickness and stress; facet angle control through growth conditions and HCl flow
• Defect Formation: threading dislocations from strain relaxation degrade junction leakage and reliability; defect density must be <10⁴ cm⁻² for acceptable yield
• Gate-to-S/D Spacing: SiGe must not contact gate; spacer width and lateral epitaxy control prevent SiGe-gate shorts; typical spacing 5-10nm

Epitaxy Process Optimization:

• Temperature: lower temperature (550-600°C) reduces dopant diffusion and provides better selectivity; higher temperature (650-700°C) improves crystal quality and growth rate
• Growth Rate: 5-15nm/min typical; slower growth provides better uniformity and selectivity; faster growth improves throughput
• HCl Flow: HCl/SiH₂Cl₂ ratio 0.1-0.5; higher HCl improves selectivity but reduces growth rate; optimization balances selectivity and throughput
• Pressure: 10-100 Torr; lower pressure improves uniformity; higher pressure increases growth rate

Advanced SiGe Techniques:

• Graded SiGe: Ge content graded from 20% at bottom to 40% at top; reduces defect density while maintaining high surface stress
• SiGe:C: carbon incorporation (0.2-0.5% C) suppresses boron diffusion and reduces defect density; enables higher Ge content without relaxation
• Raised SiGe: SiGe grown above original silicon surface (raised S/D); provides more SiGe volume for higher stress and lower contact resistance
• Condensation: grow thick SiGe, oxidize to consume Si and increase Ge concentration; can achieve 50-70% Ge for maximum stress

Reliability Considerations:

• Junction Leakage: defects in SiGe increase junction leakage; must maintain <1pA/μm leakage for acceptable off-state power
• Contact Reliability: NiSi formation on SiGe more complex than on Si; Ge segregation during silicidation affects contact resistance and reliability
• Stress Relaxation: high-temperature processing after SiGe formation causes partial stress relaxation; thermal budget management critical
• Electromigration: SiGe S/D regions have different electromigration characteristics than Si; contact and via design must account for SiGe properties

Embedded SiGe source/drain is the most effective PMOS performance booster in planar CMOS history — the combination of significant mobility enhancement (30-50%), excellent scalability, and compatibility with other strain techniques made eSiGe standard in every advanced logic process from 65nm to 14nm, finally achieving balanced NMOS/PMOS performance after decades of PMOS being the weaker device.

Source: ChipFoundryServices — Search this topic — Ask CFSGPT