Tungsten Plug Contact Fill

Before copper ever reaches a chip, tungsten gets there first: a CVD tungsten plug, wrapped in a thin titanium/titanium-nitride liner, is what actually lands the contact on silicon or silicide and carries current up to the first copper metal level, because at the depth and diameter of a modern contact hole, tungsten's deposition chemistry and mechanical properties do a job copper cannot. The sequence starts the moment the contact or via opening has been etched down through the interlayer dielectric to a landing surface — silicide over a transistor's source/drain or gate, or a lower metal line for a via — and it runs through five tightly coupled steps before the wafer is ready for the next metal level: a titanium liner that reacts with the landing surface to form a low-resistance silicide, a titanium-nitride barrier layer on top of that, a thin tungsten nucleation film grown from WF6 chemistry, a bulk tungsten CVD fill that plugs the entire hole, and a chemical-mechanical polish or etch-back that strips the blanket tungsten overburden back to the dielectric surface. Each layer exists to solve a problem the one before it created or could not solve alone: the liner fixes contact resistance and adhesion, the barrier stops fluorine from reaching silicon, and the two-step nucleation-then-bulk-fill CVD sequence is what lets tungsten fill a hole many times deeper than it is wide without leaving a void at the center.

Contact/via etch
Opening etched through ILD, landing on Si/silicide (contact) or a lower Cu line (via)
Liner + barrier
Ti liner + RTA silicide
~5-10 nm Ti sputtered or CVD, rapid thermal anneal at ~650-700°C forms low-resistance TiSi2/CoSi2 at contact bottom
TiN barrier
~5-10 nm, CVD or PVD, blocks WF6 fluorine from attacking the Ti layer and the silicon underneath
CVD tungsten fill
WF6 nucleation layer
Thin SiH4- or B2H6-reduced W seed, deposited slowly to protect the barrier before full WF6/H2 flux arrives
Bulk W CVD fill
WF6 + H2 reduction, fills contact/via center-out from the nucleation layer, no voids if nucleation was continuous
W CMP / etch-back
Blanket tungsten removed from the field, plug left flush with ILD surface, ready for M1
Contact W-plug (FEOL/MOL)Via W-plug (lower-level vias)Cu damascene (BEOL metal lines)
What it connectsTransistor source/drain silicide or gate to first metal levelOne metal level to the next, in processes that still use W for lower viasMetal line to metal line across most of the BEOL stack
Typical aspect ratioVery high, often 5:1-10:1 at advanced nodes, narrow and deepHigh, though usually shallower than a deep contactModerate, trenches are wider relative to their depth than a contact hole
Fill methodCVD nucleation + bulk WF6/H2 fill, grows inward from a conformal seedSame CVD sequence as contact fillBottom-up electroplating onto a PVD or ALD seed layer, not CVD
Why this metalTungsten's melting point and grain structure resist electromigration at contact scale, and CVD conformality fills deep narrow holes that PVD or plating alone would void or pinch offSame reasoning as contacts: reliability and fill conformality matter more than bulk resistivity this low in the stackCopper's lower bulk resistivity (~1.7 µΩ·cm vs ~5.6 µΩ·cm for W) wins once lines are wide enough that resistance, not fill conformality, dominates performance
Key failure modeFluorine attack ("wormholing") into silicon if the Ti/TiN barrier is too thin or discontinuousSame fluorine risk, plus seam voids if nucleation is incompleteElectromigration and barrier/seed discontinuity rather than fluorine attack, since no WF6 chemistry is involved
Contact Stack Cross-Section: Si to First Metal Ti liner, TiN barrier, and CVD W fill between a transistor contact and M1 Si substrate source/drain silicide (TiSi2) Interlayer dielectric (ILD) W Ti liner (~5-10 nm) TiN barrier (~5-10 nm) CVD W bulk fill M1 copper line (handed off to Cu damascene above) CMP/etch-back strips blanket W from the field, leaving the plug flush with the ILD surface Everything below M1 in this cross-section is tungsten's domain; everything at and above M1 belongs to Cu damascene

The fluorine chemistry that makes tungsten CVD possible is also the single biggest reliability risk in this entire module: WF6 is a powerful fluorinating agent, and if the TiN barrier over the Ti liner is too thin, discontinuous, or damaged, fluorine from the WF6 gas can punch through it and attack the silicon or silicide underneath, etching narrow filamentary channels — commonly called "wormholes" — directly into the substrate. This happens because the same WF6 + H2 reduction reaction that deposits tungsten on a properly nucleated surface will instead attack bare silicon directly if the fluorine reaches it before a continuous tungsten or TiN film has formed, consuming silicon and leaving behind voided, high-resistance, and sometimes electrically shorted contacts that can pass initial wafer test and fail later in the field as the damage propagates under thermal and electrical stress; this is why the nucleation step exists at all — a slower, more controlled tungsten seed deposition using silane or diborane reduction chemistry is used first, specifically because it is gentler on the underlying barrier than full WF6/H2 bulk-fill flux, and only after that seed layer is continuous does the process switch to the faster, more aggressive bulk fill chemistry. Barrier thickness, uniformity, and step coverage at the bottom corner of the contact — exactly the geometry most prone to thinning — are therefore treated as hard process-control limits, not tuning parameters, because a barrier that looks adequate across most of a wafer can still be locally thin enough at a handful of contacts to let wormholing start.

Fluorine Attack: When the Barrier Is Too Thin WF6 etches "wormholes" into silicon if Ti/TiN barrier integrity fails at the contact bottom Intact barrier Si / silicide Continuous TiN blocks fluorine; clean W fill Thin/discontinuous barrier Fluorine "wormholes" into Si through gap The nucleation layer's gentler SiH4/B2H6 chemistry exists to protect a thin or marginal barrier from full WF6 flux Wormhole damage often passes initial wafer test and surfaces later in the field under thermal/electrical stress Barrier thickness and bottom-corner step coverage are treated as hard limits, not tunable knobs, for exactly this reason

Tungsten plug formation is the hinge between the front end of the line and the copper back end of the line that sits directly above it: everything described here — contact/via etch, Ti liner silicidation, TiN barrier, WF6 nucleation and bulk fill, and W CMP — exists to land a transistor's source, drain, and gate reliably at the first metal level, a job tungsten does because its melting point and grain structure make it immune to electromigration at these tiny, high-current-density dimensions, and because CVD conformality can fill a hole far deeper than it is wide without the voids that would plague a sputtered or plated fill at that aspect ratio. Once the tungsten plug has been polished flush with the dielectric, the module this process feeds directly into takes over: via-etch-stop-dual-damascene-integration and post-etch-via-trench-ash-strip-clean open and clean the next level's geometry, pvd-barrier-seed-redeposition lines it with a Ta/TaN barrier and copper seed, and copper electroplating fills it bottom-up, with cobalt-tungsten or cobalt caps sealing each line before the next level starts — a completely different metal, deposited by a completely different mechanism, chosen because copper's lower bulk resistivity wins once a feature is wide enough that resistance matters more than fill conformality. The two metals coexist in the same chip, in the same interconnect stack, precisely because neither one is better everywhere: tungsten owns the narrow, deep, reliability-critical contacts and lower vias where CVD fill and electromigration resistance decide yield, and copper owns the wider BEOL metal lines where lower resistivity decides performance, and the handoff between them at M1 is the exact boundary this process and the Cu damascene chain above it were built to meet.

Take tungsten plug contact fill further

Ask the copilot about this term, or have our engineers assess it against your process.